Lenmar Enterprises Battery Charger R2G User Manual

LCD Display Legend  
Bad Cell Detection  
When charge process is started, the charger detects the health status of each of the cells in  
the battery compartment. If any batteries are unsuitable for charging, i.e. short circuit or  
reversed polarity, the word “BAD” will indicate on the LCD screen and ”battery” icon will flash.  
R2G802U  
USB Charge Port Operation  
When using the USB PowerPort on this charger, the AA/AAA charger function has priority.  
The USB PowerPort will not be available while batteries are installed and charging. Once the  
AA/AAA batteries have completed their charge, the USB port will be turned on automatically.  
The “USB symbol” will be shown on the LCD screen to indicate the USB socket is  
ready for use.  
Fig. 1  
Note: Make sure the maximum loading is not exceeding 500mA for the USB socket. Do not  
attempt to overload the USB port or damage to the charger or USB device may result.  
PLEASE READ THE INFORMATION AND FOLLOW ALL INSTRUCTIONS THOROUGHLY BEFORE  
USING THIS PRODUCT.  
Getting Ready  
Choose the adapter plate for the type of battery you will be charging. Each of the adapter  
plates is labeled as to the batteries it can work with. If the charger base does not already  
have the adapter plate you want attached, you will need to remove the adapter plate first  
by pushing down on the plate and sliding it to the rear of the charger base (away from  
the LED indicators). Then, attach the selected adapter plate to the charger unit by  
aligning the arrows on the sides of the adapter plates and the charger base as shown.  
While pressing down lightly on the adapter plate, slide the plate toward the front of the  
charger base until it locks.  
Introduction  
Clock / Alarm / Day-Date operation  
Thank you for purchasing the R2G802 2 Hour Charger. Read the instruction manual  
thoroughly before use and keep the manual for later reference. It contains important  
operating instructions for your R2G Rechargeable Battery System. The R2G802 is a  
combination of Travel Alarm Clock, 2 hour microprocessor controlled charger for 1 to 4  
AA/AAA NiMH batteries, Thermometer, and USB PowerPort for charging your cell  
phones, MP3 players or any other device that accepts power from a USB port. All the  
functions are displayed clearly on a large backlit LCD Display. The charger can be  
powered 3 ways and includes a high efficiency “switching” type power supply will adjust  
automatically to any voltage from 100 – 240VAC, for international use. A car-cord for  
using the charger in the car and a USB cable for powering the charger from your  
computer are also included.  
The following shows which buttons on the setting panel you need to press to navigate  
between modes. The 2 feet on the bottom rear of the chassis act as switches to activate the  
blue backlight on the LCD display. In any mode, just to hit the top of the unit lightly and the  
black light will light on for about 10 seconds. The backlight will only operate while the unit is  
plugged into power using any of the supplied power adapters.  
Charging Instructions  
Setting the Time and Date  
Fig. 2  
1. Choose the source of power for the charger unit. You can use the AC adapter which  
is international capable accepting 100-240VAC (plug adapter may be required in other  
countries, not included), the DC car cord while on the move or plugged into a USB port  
on your computer (charge times are increased when USB power is used). Simply plug  
the desired power cable into the side of the charger unit and the other end into the  
appropriate power source.  
Before Use  
To activate the clock and thermometer functions, pull out the tab from the side of the  
casing at the access cover to the clock battery on the bottom of the unit. The clock  
portion of the LCD display will turn on and you will hear alarm music for 10 seconds. The  
Clock / Alarm is now ready for use and should be set to the proper time / date. If the LCD  
display get dim or the sound of the alarm tone become weak, replace the clock battery  
with another new “CR-2025” type 3V Lithium battery which is located on the bottom side  
of the charger base.  
B
In the regular Time mode, press the  
button once and the “Time” icon will starts to flash on  
2. Insert 1 to 4 pieces of AA or AAA rechargeable Ni-MH batteries into any open battery  
location observing the proper battery polarity to the marks in the battery compartment.  
Do not mix AA and AAA batteries while charging. The Blue backlight will light up for  
around 10 sec once the batteries inserted correctly. For charging AAA batteries, pull  
down the adjustable battery contact plate before inserting the AAA batteries into the  
compartment. The charger automatically adjusts the charging current depending on the  
size of the battery being charged.  
the LCD screen along with the item to be changed, which indicates Time Setting mode. Use  
C
and  
what you want, press  
can be set in the range of 2000 to 2099. The day of the week is calculated automatically  
D
buttons to change the value of the flashing item. Once the flashing item is set to  
B
to select the next setting and change as listed above. The “Year”  
A
according with the date you set. Once all the items are set, press the  
button to exit the  
Caution:  
setting mode (set mode will automatically if there is no input for 1 minute). The following figure  
shows the order of items during the setting process.  
Batteries are partially charged as shipped. Must be charged prior to first use for full  
capacity.  
3. The LCD will indicate the proper charging and the word “Charge” will be shown to the  
left of the battery symbols that indicate each battery’s charge progress. After the  
batteries are fully charged, the wording “FULL” will indicate on the LCD screen to  
indicate the trickle charge and the charged batteries are ready for use. Once charge is  
complete, remove batteries and unplug the charger as soon as it is practical. Do not  
leave batteries in charger for extended periods of time (more than 1-2 days) or when the  
charger is not plugged in. Unplug the charger when not in use.  
Charge only NiMH type batteries on this charger.  
Do Not mix AA and AAA or different capacity batteries together when charging  
Use only R2G, NoMEM PRO or other proper NiMH compatible charger to recharge  
the batteries included.  
Fig. 3  
Batteries may leak or explode causing personal injury if inserted improperly, disposed  
of in fire, mixed with other battery types, or short circuited.  
12/24 Hour Mode:  
C
In the regular Time mode, pressing the  
24-hour mode.  
button will toggle between 12-hour and  
4. Begin again at Step-1 to charge the next set of batteries.  
2.  
1.  
3.  
 

Krups Egg Cooker F230 User Manual
Lathem Time Clock FR700 User Manual
Lego Games 79011 User Manual
Logitech Webcam 622866 1403 User Manual
Magnavox Flat Panel Television 32MF339B F7 User Manual
Maytag Dishwasher mdb8600awb User Manual
Maytag Double Oven MET8885XS User Manual
Melissa Snow Blower 670 014 User Manual
Memorex MP3 Player MPD8842 User Manual
Mercedes Benz Automobile 2004 E 320 User Manual