Lenovo Computer Hardware 8252 User Manual

Hardware Replacement Guide  
Lenovo 3000 J Series  
Types 8252, 8253, 8254, 8257, 8258, 8259  
 
Lenovo 3000 J Series  
 
First Edition (December 2005)  
© Copyright Lenovo 2005.  
Portions © Copyright International Business Machines Corporation 2005.  
All rights reserved.  
U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with  
RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule  
contract with Lenovo Group Limited, if any, or the standard terms of this commercial license, or if the agency is  
unable to accept this Program under these terms, then we provide this Program under the provisions set forth in  
Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in  
Data-General, FAR 52.227.14 (Alternate III).  
 
iv Hardware Replacement Guide  
 
Overview  
This guide is intended to be used by customers who are replacing Customer  
Replaceable Units (CRUs) as well as trained service personnel who are replacing  
Field Replaceable Units (FRUs). In this document, CRUs and FRUs will be referred  
to as parts.  
Note: Trained service personnel should refer to the Hardware Maintenance  
Manual(HMM) for parts ordering information.  
This guide does not include procedures for all parts. It is expected that cables,  
switches, and certain mechanical parts can be replaced by trained service personnel  
without the need for step-by-step procedures.  
This guide contains instructions for replacing the following parts:  
Note: Use only the parts provided by Lenovo.  
v Memory module  
v PCI adapter card  
v Keyboard  
v Mouse  
Safety information for replacing CRUs  
Do not open your computer or attempt any repair before reading the “Important  
safety information” in the Quick Reference that was included with your computer.  
To obtain a copy of the Quick Reference go to the World Wide Web at  
Safety information for replacing FRUs  
Do not open your computer or attempt any repair before reading the “Important  
safety information” in the Hardware Maintenance Manual (HMM) for the computer.  
To obtain a copy of the HMM, go to the World Wide Web at  
Additional information resources  
If you have Internet access, the most up-to-date information for your computer is  
available from the World Wide Web.  
You can find the following information:  
v CRU removal and installation instructions  
v CRU removal and installation videos  
v Publications  
v Troubleshooting information  
v Parts information  
v Downloads and drivers  
v Links to other useful sources of information  
v Support phone list  
© Lenovo 2005. Portions © IBM Corp. 2005.  
v
 
 
Tools required  
To replace some parts in your computer, you might need a flat-blade or Phillips  
screwdriver. Additional tools might be needed for certain parts.  
Handling static-sensitive devices  
Static electricity, although harmless to you, can seriously damage computer  
components and parts.  
When replacing a part, do not open the static-protective package containing the  
new part until the defective part has been removed from the computer and you are  
ready to install the new part.  
When you handle parts and other computer components, take these precautions to  
avoid static-electricity damage:  
v Limit your movement. Movement can cause static electricity to build up around  
you.  
v Always handle parts and other computer components carefully. Handle  
adapters, memory modules, system boards, and microprocessors by the edges.  
Never touch any exposed circuitry.  
v Prevent others from touching the parts and other computer components.  
v Before you replace a new part, touch the static-protective package containing the  
part to a metal expansion-slot cover or other unpainted metal surface on the  
computer for at least two seconds. This reduces static electricity in the package  
and your body.  
v When possible, remove the new part from the static-protective packaging and  
install it directly in the computer without setting the part down. When this is  
not possible, place the static-protective package that the part came in on a  
smooth, level surface and place the part on it.  
v Do not place the part on the computer cover or other metal surface.  
vi Hardware Replacement Guide  
 
 
Chapter 1. Locations  
This chapter provides illustrations to help locate the various connectors, controls  
and components of the computer. To open the computer cover, see “Removing the  
Locating the connectors on the front of your computer  
The following illustration shows the location of connectors on the front of the  
computer.  
ꢀ1ꢁ  
ꢀ2ꢁ  
Headphone connector  
Microphone connector  
ꢀ3ꢁ  
ꢀ4ꢁ  
USB connector  
USB connector  
© Lenovo 2005. Portions © IBM Corp. 2005.  
 
1
 
Locating the connectors on the rear of your computer  
The following illustration shows the location of connectors on the rear of the  
computer.  
ꢀ1ꢁ Power connector  
ꢀ2ꢁ Voltage switch  
ꢀ9ꢁ Ethernet connector  
ꢀ10ꢁ USB connectors  
ꢀ3ꢁ Mouse connector  
ꢀ4ꢁ Keyboard connector  
ꢀ5ꢁ Serial connector  
ꢀ6ꢁ Parallel connector  
ꢀ7ꢁ VGA monitor connector  
ꢀ8ꢁ USB connectors  
ꢀ11ꢁMicrophone connector  
ꢀ12ꢁAudio line out connector  
ꢀ13ꢁAudio line in connector  
ꢀ14ꢁAGP connector  
ꢀ15ꢁPCI connectors  
2
Hardware Replacement Guide  
 
 
Locating components  
The following illustration will help you locate the various components in your  
computer.  
ꢀ1ꢁMicroprocessor and heat sink  
ꢀ2ꢁMemory modules  
ꢀ4ꢁPCI connectors  
ꢀ5ꢁPCI adapter  
ꢀ3ꢁAGP connector  
ꢀ6ꢁPower supply  
Chapter 1. Locations  
3
 
 
Identifying parts on the system board  
The system board (sometimes called the planar or motherboard) is the main circuit  
board in your computer. It provides basic computer functions and supports a  
variety of devices.  
The following illustration shows the locations of parts on the system board for  
some models.  
ꢀ1ꢁ Microprocessor and heat sink  
ꢀ2ꢁ Microprocessor fan connector  
ꢀ3ꢁ Memory connector 1  
ꢀ4ꢁ Memory connector 2  
ꢀ5ꢁ Power connector  
ꢀ6ꢁ Diskette drive connector  
ꢀ7ꢁ Secondary IDE connector  
ꢀ8ꢁ Primary IDE connector  
ꢀ9ꢁ Battery  
ꢀ10ꢁSATA connectors (2)  
ꢀ11ꢁClear CMOS/Recovery jumper  
ꢀ12ꢁPower LED connector  
ꢀ13ꢁFront USB connector  
ꢀ14ꢁFront audio connector  
ꢀ15ꢁPCI connectors  
ꢀ16ꢁAGP connector  
ꢀ17ꢁSystem fan connector  
ꢀ18ꢁ12v power connector  
4
Hardware Replacement Guide  
 
 
The following illustration shows the locations of parts on the system board for  
some models.  
ꢀ1ꢁ Microprocessor and heat sink  
ꢀ2ꢁ Microprocessor fan connector  
ꢀ3ꢁ Memory connector 1  
ꢀ4ꢁ Memory connector 2  
ꢀ5ꢁ Power connector  
ꢀ11ꢁFront panel connector  
ꢀ12ꢁPower LED connector  
ꢀ13ꢁClear CMOS/Recovery jumper  
ꢀ14ꢁFront USB connectors (2)  
ꢀ15ꢁBattery  
ꢀ6ꢁ Diskette drive connector  
ꢀ7ꢁ Primary IDE connector  
ꢀ8ꢁ Secondary IDE connector  
ꢀ9ꢁ System fan connector  
ꢀ10ꢁSATA connectors (2)  
ꢀ16ꢁPCI connectors  
ꢀ17ꢁFront audio connector  
ꢀ18ꢁAGP connector  
ꢀ19ꢁ12v power connector  
Chapter 1. Locations  
5
 
6
Hardware Replacement Guide  
 
Chapter 2. Replacing hardware  
Attention  
Do not open your computer or attempt any repair before reading the “Important safety  
information” in the Quick Reference that was included with your computer or in the  
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Quick  
Note: Use only the parts provided by Lenovo.  
Removing the cover  
Important  
Turn off the computer and wait 3 to 5 minutes to let the computer cool  
before opening the computer cover.  
To remove the cover:  
1. Shut down your operating system, remove any media (diskettes, CDs, or tapes)  
from the drives, and turn off all attached devices and the computer.  
2. Unplug all power cords from electrical outlets.  
3. Disconnect all cables attached to the computer. This includes power cords,  
input/output (I/O) cables, and any other cables that are connected to the  
computer.  
© Lenovo 2005. Portions © IBM Corp. 2005.  
 
7
 
4. Remove the two screws at the rear of the left side cover and slide the cover to  
the rear to remove.  
Replacing a memory module  
Attention  
Do not open your computer or attempt any repair before reading the “Important safety  
information” in the Quick Reference that was included with your computer or in the  
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Quick  
This section provides instructions on how to replace a memory module.  
Note: Your computer has support for two or four memory modules.  
1. Remove the computer cover. See “Removing the cover” on page 7.  
8
Hardware Replacement Guide  
 
 
2. Remove the memory module being replaced by opening the retaining clips as  
shown.  
3. Position the replacement memory module over the memory connector. Make  
sure that the notch ꢀ1ꢁon the memory module aligns correctly with the  
connector keyꢀ2ꢁ on the system board. Push the memory module straight  
down into the memory connector until the retaining clips close.  
Replacing a PCI adapter  
Attention  
Do not open your computer or attempt any repair before reading the “Important safety  
information” in the Quick Reference that was included with your computer or in the  
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Quick  
Chapter 2. Replacing hardware  
9
 
 
This section provides instructions on how to replace a PCI adapter.  
1. Remove the computer cover. See “Removing the cover” on page 7.  
2. Remove screw from adapter.  
3. Remove the adapter by pulling it straight out of the adapter connector.  
4. Remove the new adapter from its static-protective package.  
5. Install the new adapter into the appropriate slot on the system board.  
6. Secure adapter with the screw as shown.  
Replacing a keyboard  
Attention  
Do not open your computer or attempt any repair before reading the “Important safety  
information” in the Quick Reference that was included with your computer or in the  
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Quick  
This section provides instructions on how to replace a keyboard.  
1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down your  
operating system, and turn off all attached devices.  
2. Unplug all power cords from electrical outlets.  
10 Hardware Replacement Guide  
 
 
3. Locate the keyboard connector.  
Note: Your keyboard might be connected to a standard keyboard connector  
ꢀ1ꢁor a USB connector ꢀ2ꢁ. Depending on where your keyboard is  
4. Disconnect the failing keyboard cable from the computer.  
5. Connect the new keyboard to the appropriate connector on the computer.  
Replacing a mouse  
Attention  
Do not open your computer or attempt any repair before reading the “Important safety  
information” in the Quick Reference that was included with your computer or in the  
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Quick  
This section provides instructions on how to replace a mouse.  
1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down your  
operating system, and turn off all attached devices.  
2. Unplug all power cords from electrical outlets.  
3. Locate the mouse connector.  
Note: Your mouse might be connected to a standard mouse connector ꢀ1ꢁor a  
USB connector ꢀ2ꢁ in the front or rear of your computer. See “Locating  
4. Disconnect the failing mouse cable from the computer.  
Chapter 2. Replacing hardware 11  
 
 
5. Connect the new mouse to the appropriate connector on the computer.  
Completing the parts replacement  
After working with parts, you need to replace the computer cover and reconnect  
any cables, including telephone lines and power cords. Also, depending on the  
part that was replaced, you might need to confirm the updated information in the  
Setup Utility program.  
1. Ensure that all components have been reassembled correctly and that no tools  
or loose screws are left inside your computer.  
2. Reposition any cables that might impede the replacement of the cover.  
3. Close the computer cover.  
4. Install any locking devices such as a padlock as necessary.  
5. Reconnect the external cables and power cords to the computer. See “Locating  
6. To update the configuration, see Starting the Setup Utilityin the Quick  
Reference that was included with your computer.  
Note: In most areas of the world, Lenovo requires the return of the defective CRU.  
Information about this will come with the CRU or will come a few days  
after the CRU arrives.  
12 Hardware Replacement Guide  
 
 
Appendix. Notices  
Lenovo may not offer the products, services, or features discussed in this  
document in all countries. Consult your local Lenovo representative for  
information on the products and services currently available in your area. Any  
reference to a Lenovo product, program, or service is not intended to state or  
imply that only that Lenovo product, program, or service may be used. Any  
functionally equivalent product, program, or service that does not infringe any  
Lenovo intellectual property right may be used instead. However, it is the user’s  
responsibility to evaluate and verify the operation of any other product, program,  
or service.  
Lenovo may have patents or pending patent applications covering subject matter  
described in this document. The furnishing of this document does not give you  
any license to these patents. You can send license inquiries, in writing, to:  
Lenovo (United States), Inc.  
500 Park Offices Drive, Hwy. 54  
Research Triangle Park, NC 27709  
U.S.A.  
Attention: Lenovo Director of Licensing  
LENOVO GROUP LTD. PROVIDES THIS PUBLICATION “AS IS” WITHOUT  
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some  
jurisdictions do not allow disclaimer of express or implied warranties in certain  
transactions, therefore, this statement may not apply to you.  
This information could include technical inaccuracies or typographical errors.  
Changes are periodically made to the information herein; these changes will be  
incorporated in new editions of the publication. Lenovo may make improvements  
and/or changes in the product(s) and/or the program(s) described in this  
publication at any time without notice.  
The products described in this document are not intended for use in implantation  
or other life support applications where malfunction may result in injury or death  
to persons. The information contained in this document does not affect or change  
Lenovo product specifications or warranties. Nothing in this document shall  
operate as an express or implied license or indemnity under the intellectual  
property rights of Lenovo or third parties. All information contained in this  
document was obtained in specific environments and is presented as an  
illustration. The result obtained in other operating environments may vary.  
Lenovo may use or distribute any of the information you supply in any way it  
believes appropriate without incurring any obligation to you.  
Any references in this publication to non-Lenovo Web sites are provided for  
convenience only and do not in any manner serve as an endorsement of those Web  
sites. The materials at those Web sites are not part of the materials for this Lenovo  
product, and use of those Web sites is at your own risk.  
Any performance data contained herein was determined in a controlled  
environment. Therefore, the result obtained in other operating environments may  
© Lenovo 2005. Portions © IBM Corp. 2005.  
 
13  
 
vary significantly. Some measurements may have been made on development-level  
systems and there is no guarantee that these measurements will be the same on  
generally available systems. Furthermore, some measurements may have been  
estimated through extrapolation. Actual results may vary. Users of this document  
should verify the applicable data for their specific environment.  
Television output notice  
The following notice applies to models that have the factory-installed  
television-output feature.  
This product incorporates copyright protection technology that is protected by  
method claims of certain U.S. patents and other intellectual property rights owned  
by Macrovision Corporation and other rights owners. Use of this copyright  
protection technology must be authorized by Macrovision Corporation, and is  
intended for home and other limited viewing uses only unless otherwise  
authorized by Macrovision Corporation. Reverse engineering or disassembly is  
prohibited.  
Trademarks  
Lenovo is a trademark of Lenovo in the United States, other countries, or both.  
IBM is a trademark of the International Business Machines Corporation in the  
United States, other countries, or both.  
Other company, product, or service names may be trademarks or service marks of  
others.  
14 Hardware Replacement Guide  
 
 
 
Part Number: 41T3793  
Printed in USA  
(1P) P/N: 41T3793  
 

Krown Manufacturing Amplified Phone KR2812 User Manual
Lanier Printer GX3050N User Manual
Lennox Hearth Indoor Fireplace RAD22C 2 User Manual
Lennox Hearth Outdoor Fireplace ODGHK36 User Manual
Lenoxx Electronics Home Theater System HT 395 User Manual
LG Electronics Range LRE3023SB User Manual
LG Electronics Washer WM1811CW User Manual
Lowrance electronic GPS Receiver HDS 5M User Manual
Mazda Automobile CX 9 User Manual
MicroBoards Technology DVD Recorder 820 00151 01 User Manual