INSTALLATION INSTRUCTIONS FOR PART 95-5822B
APPLICATIONS
2009-10 FORD F-150
LARIAT / KING RANCH / PLATINUM MODELS
(Not for NAV Equipped Models)
95-5822B - BLACK
95-5822AS – PLATINUM / ASH SATIN
95-5822CM - KING RANCH / CURLY MAPLE
95-5822MM – LARIAT / MILANO MAPLE
KIT FEATURES
• Double DIN Head Unit Provision
• Stacked ISO DIN Head Unit Provision
• Painted or Wood Grain
KIT COMPONENTS
• A) Double DIN Radio Housing • B) Double DIN Radio Housing Brackets
• C) Radio Housing Trim Panel • D) (6) U Style Panel Clips
A
D
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
Harness:
specific interface harness
Antenna Adapter:
• 40-CR10 - Chrysler antenna adapter 02-up
C
B
TOOLS REQUIRED:
• Phillips Screwdriver • Socket Wrench • Panel Removal Tool • Cutting Tool
• Torx Driver
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
95-5822B DASH DISASSEMBLY
2009-10 FORD F-150
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
2
Unclip and remove the switch panel
to the right of the cigarette lighter
then remove the (1) 9/32” screw
exposed. (Figure A)
3
4
Remove the rubber pad at the top of
the radio trim panel then remove the
(2) 9/32” screws exposed. (Figure B)
Unclip and pull the side panels con-
taining the a/c vents away from the
radio trim panel. Note: It is not nec-
essary to remove the panels com-
pletely. (Figure C)
B
5
Unclip and remove the radio trim
panel. (Figure D)
Continued on page 2.
C
D
1
95-5822B DASH DISASSEMBLY
FORD F-150 2009
E
6
Unclip and remove the hazard/airbag
switch and driver info switch assem-
blies from the factory radio trim
panel. (Figure E)
7
8
9
Unclip and remove the cigarette
lighter socket from the radio trim
panel. (Figure F)
Remove (4) Torx screws securing the
factory climate control to the radio
trim panel. (Figure G)
F
Remove (4) 9/32” screws to remove
the factory radio.
Continue to final preparation.
G
2
95-5822B KIT ASSEMBLY
FORD F-150 2009
A
1
2
3
4
Clip the hazard/airbag switch and
driver info switch assemblies into
the radio housing in the same loca-
tion as the factory radio trim panel.
Clip the cigarette lighter socket into
the radio housing in the same loca-
tion as the factory radio trim panel.
(Figure B)
Secure the climate control into the
radio housing using the factory
hardware in the same location as
the factory radio trim panel. (Figure C)
B
Attach the (6) U style panel clips to
the radio housing in the same
location as the factory radio trim
panel. (Figure D)
Continue to kit assembly.
C
D
KIT REPLACEMENT RADIO TRIM PANEL-REAR VIEW
KIT REPLACEMENT RADIO TRIM PANEL-REAR VIEW
3
95-5822B KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION OR
STACKED ISO MOUNT UNIT(S) PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
1
2
Slide the appropriate side bracket
over the mounting legs of the Double
A
DIN trim plate aligning the holes in
the trim plate and the bracket and
rotate inward.
Note: The notch in the housing
should be on top. (Figure A)
Slide the Double DIN or stacked ISO
mount units into the bracket/radio
housing assembly and secure the
Double DIN or stacked ISO mount
units to the assembly using the
B
screws supplied with the Double DIN
or stacked ISO mount units. (Figure B)
3
Cut and remove half of the top (2)
mounting legs with the brackets
attached. (Figure C)
Continue to final assembly.
C
4
95-5822B FINAL ASSEMBLY
FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
C
D
D) Tape
Locate the factory wiring harness in the dash. Metra recommends using the proper mating
adapter and making the connections as shown. (Isolate and individually tape off the ends of
any unused wires to prevent electrical short circuit).
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly using the
95-5822B radio housing in place of the factory radio trim panel.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions
included with the head unit. Metra recommends making connections shown below; Strip, Splice,
Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short
circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be
present on all leads due to manufacturer’s specifications.
5
95-5822B INSTRUCTIONS
1-800-221-0932
REV. 05/21/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST95-5822B
|